Horrible Things for Hotties

“This is a quick zone assignment. Given a set of electronic tools and supplies, you have 45 minutes to complete a torture for your hottie.”

<45 minutes pass, but the viewers only see short bits of the elapsed time>

“OK let’s see what our torture technicians have come up with. What have you done here, Jeff?”

“Well, I was thinking about the basics of electronics, electricity, and went with a simple stripped power cable tapped to her nipples and plugged into the wall.”

“OK let’s see it in action!”

Jeff plugs in his “torture cable”. His hottie screams for about  30 seconds then collapses, falling off her chair onto the ground, where she lies, lifeless.

“OK, unplug it now.  Looks like you snuffed your hottie, so you are not going to advance as this was a torture assignment, not a snuff assignment.  Sorry about that. Moving on.  What have you done here Lewis?

“Well, as it happens I do know a thing or two about electronics so I bread boarded a simple square wave pulse generator which leads to these two copper wires.  What I need to do for the torture is pierce her nipples with the wires, solder them shut, then turn on the generator, which will supply a high voltage, but low amperage jolt to each nipple, each jolt lasting 2 seconds,  more or less and with a 3 second delay before changing nipples.  Due to the way that I’m grounding the system, at no times does the shortest path to ground pass through her heart, plus the jolt should be low enough amperage, that even if it does pass through her heart it should not be fatal.”

“OK, let see it in action.”

With that Lewis takes the two wires from the work bench and pushes them through his hotties nipples.

“I’ve cut them at a diagonal to make them sharp, but I’m sure this hurts.  Not really part of the torture, but a nice touch any way…

After piercing her nipples, he wraps the connection wires around the nipple piercing wire, about a quarter inch away from the nipple.

OK, now I’m going to solder the wire on to the piercing wire,   I do count this a part of the torture, because, well solder melts at about 370 °F, which should raise, at least, some blisters on her nipples from the conduction of the heat over the copper wires.  Normally I would put a heat sink on the wire to prevent it from transferring the heat to other parts of the system, but in this case I want it to happen.  I’ve stuffed a rag into her mouth so I will not be distracted by her screaming while I do this.  Don’t want to mess up this part of the project.  I’ve tied her to the chair with some CAT-5 cable so she will stay in place.”

Lewis begins to solder the wires in place. His hottie thrashes about and screams into the rag in her mouth.

“OK the first one is done”

Lewis moves on to the second wire and quickly solder it shut as well.

“OK I’m cheating here a bit, I’m just going to tape the ground wires to her tits, just about an inch from her nipples…  I though about making them sharp  and pushing them into her tits, but I couldn’t think of a way to keep them in when she jumps from a jolt, so I’m making  a circle from the stripped part of the ground wire and taping that down.”

“Looks like you have it all under control.  Want to turn it on now?”

Lewis pull the rag from his hotties mouth, then flips a switch on his circuit bread board.

“It will take about 5 seconds to start the R/C time parts of the circuit to ‘warm up'”

As soon as he finishes saying that, his hottie jerks and lets out a yelp.  A few seconds later she does it again.

“OK, how long do you want this to run?  This should last until the power is turned off with no permanent physical damage to her.  I’m not going to say no mental damage, because I suspect this will break her will in less than an hour.”

 


And we will back to Horrible Things for Hotties after these commercial messages.

Do you have a slave that needs to be flogged?  But don’t have the time or energy to do it yourself?  Don’t want to pay outrageous fees to have Mistress do it for you?  Well, we have the answer to your problems.  Introducing the Flogger-2020 a newly designed system that isn’t just a spinning wheel with a whip attached, but is actually a snapping whip, with realistic arm like snapping action.  Imported from Germany, this system is the last word in hands off slave punishment!

The Flogger 2020

The secret is in the patented offset cam system, which combined with the state of the art computer control system insure a proper snap each and every time.  The Flogger-2020 can be fitted with a wide range of implements to deliver exactly the punishment your slave needs.  The system can be set for constant action, where the slave receives 1 stroke on a set time, ranging from one per 5 seconds to once a minute, or it can be set on random time, so the slave never knows when the next stroke will land.

Flogger 2020 with wooden horse.

The Flogger 2020 has a full 3 axis of mobility to the flogging head, so it can be used on slaves in both a standing position and on slaves in a more traditional wooden horse.  It’s ideal for all your flogging needs!

Call 1 866-555-FLOG that’s 1-866-555-3564 for more information on this ground breaking flogging system.  Operators are standing by waiting on your call!  Mention this ad and receive a $200 discount on they system.  Be one of the first 100 callers and get either a standing flogging post or a wooden horse for only $150 more!  Don’t wait, call now!  Call now and receive two videos showing the Flogger 2020 in action!


Titanium Steel Ball-gag

Ball gags.  Every body uses them, they are great for making you slave be silent,  but do you have the problem of your slave biting into them an destroying your gag?   That’s a thing of the past with the new titanium steel gag from Gag-a-million!  We don’t care how hard she bites with these, she isn’t going to damage them.  Made from armor grade titanium steel alloy they will withstand any thing short of 20mm autocannon rounds, much more than your average slave is going to have access to!